50a PID Complete Control Panel Kit
Basic Kit Hardware
- 6 - LEDs (2 white 220v, 2 yellow 110v, 1 red 110v, and 1 green 220v)
- 1 - Alarm Buzzer LED
- 1 - Emergency Stop locking push button with NC Contact
- 2 - 2-Way Switches with NO Contacts for element (on-off)
- 2 - 2-Way Switches with NO Contacts for pumps (on-off)
- 3 - 2-Way Toggle style Blue LED Switches with NO/NC Contacts for pumps (on-off)
- 1 - 2-Way Switches with NO Contacts for alarms (on-off)
- 1 - Additional NO Contacts for back of emergency stop
- 4 - Additional NC Contacts for back of 2-way switches
- 1 - Key toggle Switch for panel on/off
- 1 - General Purpose Ice Cube Style Relay for safe power up
- 3 - 63a DIN Contactors w/ 110v Coils for main power and for element control
- 2 - 40a Solid State Relays for elements
- 1 – Large (US made) pre-drilled and tapped heat sink for element SSRs
- 1 meter of DIN rail cut in 1/3m increments
- Phoenix Contact Terminal Blocks for wire from 6-24 awg
- 2 - UL-Listed 32a 2 pole DIN Rail Breaker
- 1 - UL-Listed 6a 1 pole DIN Rail Breaker
- Phoenix Contact Terminal Block clip style anchoring ends
- Phoenix Contact Terminal Block end covers
- Terminal bridge jumpers
Enclosure and outlets
- 1 – Enclosure (pre-cut US-Made stainless steel)
- 2 – L6-30 Flanged outlets for elements
- 2 – L5-15 Flanged outlets for pumps
- 1 - 5-15 Auxilary side mount outlet
- 1 – C6375 flanged inlet for main power supply
- 3 – XLR Male pre-wired and solderd connectors for temperature input
- Tags for panel include:
- Power / Off-On
- Alarm / Off-On
- Stop
- Boil Element / Off-On
- HLT Element / Off-On
- Water Pump / Off-On
- Wort Pump / Off-On
- 2 x HLT
- 2 x Boil
- Mash
- Water Pump
- Wort Pump
- HLT Probe
- MASH Probe
- Boil Probe
- 240v / 50a
- 120v / 6a
- Reset
- Start
PID Temp controller, PID Timer and temperature probes
- 3 - EBSP200 (SSR Output) PID Temperature control units
- 1 - EBST200 PID Timer unit
- 3 - 1/2 inch MPT x 1-1/2 inch RTD100 Temperature Probes
- 3 – XLR to QC Silicon temperature probe cables
Wiring and wire fittings
- 6 ft Range style main power cable with 14-50 end
- Black 6 gauge wire
- Black 10 gauge wire
- Red 10 gauge wire
- Green 10 gauge wire
- Black 14 gauge wire
- Red 14 gauge
- White 14 gauge wire
- Yellow 14 gauge wire
- Orange 14 gauge wire
- Blue 14 gauge wire
- Purple 14 gauge wire
- Pink 14 gauge wire
- Red 18 gauge wire
- Yellow 18 gauge wire
- Orange 18 gauge wire
- White 18 gauge wire
- 10 - #10 Yellow Spade connectors for 10ga wire connections on SSR relays
- 100 - #6 Blue Spade Connectors for most 110v wiring throughout the panel
- 50 - #6 Red spade connectors for the low voltage and temp probe wiring
- 5 - #10 Blue ring connectors for grounding wire on enclosure posts
- Approx. 50 Nylon Adhesive Back Cable tie bases (zip tie base)
- Nylon cable ties (1/8" x 4.1")
Package also includes a printed copy of our wiring guide.
Tools you will need include:
- Wire Cutters
- Wire strippers
- Crimping tools for spade and ring connectors
- Phillips screw driver(s)
- Flat head screw driver(s)
Important note, while we are a UL control panel shop, these kits cannot be UL Listed only products we expressly build and state as such on our site are UL listed. This is especially important to note for those intending to use this for commercial purposes within the US or in Canada.
PID Controllers | EBSP200 Temperature Controllers |
Full load amperage: | 48.25 amps @ 240v |
Max Output: | (2) 5500w Elements and (2) Brewery Pumps @ 1.2 amps |
Power outlet: | 14-50 Range style, requiring Neutral and Ground |
Power cord: | 6 foot molded cord with CS6364C connector |
Power in: | CS6375 Flanged inlet 240v with ground and neutral.
Panel uses and provides 120v for control and for pumps |
Panel outputs: |
(2) L6-30 flanged outlets for elements (2) L5-15 flanged outlet for pumps (1) Side 5-15 auxiliary outlet |
Panel inputs: |
(3) XLR inputs with QC variant cables for NPT and TC probes |
Enclosure: |
Stainless Steel Nema 4x Enclosure 16ga Enclosure Walls, 14ga Enclosure door thickness 16 in (W) x 18 in (H) x 8.5 in (D) 400mm x 450mm x 225mm UL Listed Enclosure VESA 200x200 Mounting points, 6mm-1 screws on back |
Included in the box: |
(1) Control Panel (1) Power cord for panel (3) Temp probe cables (X) Temp probes dependent on selection |
Certifications: | Controller is not certified UL |
Point of origin: |
Terminal blocks, breakers and power from EU PID Controllers, outlets, contactors and SSRs from China Enclosures made in USA |
Warranty: | 30 days parts |
All panel kits are assembled by Electric Brewing Supply, in Chassell, Michigan from globally sourced parts.
![]() |
![]() |
Introducing the all new Electric Brewing Supply EBSP200 Next gen PID Controller. Active display for easy read, large digits for reading from a distance. Backlit display with alert indicators. Digital PID Temperature Controller, Auto/Manual Control function PID Auto-tuning Alarm output function Output: Relay our SSR Drive Digital PID Temperature Controller |
Our exclusively designed and built, backlit display timer unit. Designed for the sole purpose of count down or count up times. Simple control use. Alarm output, multi step capable. Alarm only (no temp control) Relay Output only Power supply: 85~265Vac 50/60HZ |
NPT Style Probe
|
Tri-Clamp Style Probe |
NPT Are also available in 4 and 8 inch lengths
Tri-Clamp are also available in a 7 inch length
![]() |
Assembled Tri-Clamp Element for heating Available starting at $190 Each |
![]() |
L5-15 to 5-15 jumper cables Recommended for between the pump and your panel. Available for $15 each |
![]() |
Heavy Duty VESA 200x200 Fixed Wall Mount Recommended for quick and easy mounting of your control panel. Available for $30 each |
- Complete Wiring Guide (2018 REV)
- Complete Wiring Guide (2022 Rev) COMING SOON
- Specific Wiring Schematic for 2018 Rev (30"x24" plotter sized)
- Specific Wiring Schematic for May 2021 to present (30"x24" plotter sized)
- Getting Started Manual
- EBSP200 Temperature Controller Manual
- EBST200 Timer Manual